Curtis Ellis 2018 N.A.M.S Champion
  Fastest 4CYL's In Alberta

NorthernAlbertaMiniStocks

Click here to edit subtitle

Northern Alberta Mini Stocks - Bandits

NAMS Safety and Race Format

-Safety (Minimum Requirements)

1. Leather high top shoes/boots and gloves.,no running shoes. Racing

gloves and boots highly recommended

2. Flame resistant suit designed for auto racing (mandatory)

3 Snell 2010 or newer full face helmet.

4. Latch type 5 point 3" seat belts no older than 2012 dated, requires Sub

belt.

5. Driver's window net with quick release.

6. High-back Racing seat mounted to roll cage.

7. Driver's area roll bars must be padded.

8 Battery must be securely fastened with a non/conductive cover over the positive battery terminal. Battery must be in protective battery box (plastic marnie style boxes allowed) if located in drivers area

9.Must have a battery kill switch properly marked within arms reach of the drivers window, so safety personal can shut off car and check on driver at same time.

10. All cars must have a fire extinguisher within their pit stall. Min.5 lbs

11. No Antifreeze allowed in any car . No exceptions

- Format

1 All cars will register their car number for $50.00 (First come first served) .Unregistered cars will be allowed to race with the Northern Alberta Mini Stock tour but will not be eligible to Collect N.A.M.S. Points, Payout , Trophys etc.

1A Numbers will be held for 1 full year,unless ok'd in writing by last years registered owner that it will be ok if number be used.

1B. All Bandit Cars will need the letter "B" either before or after the car number. Min of 3in tall on doors, 5in tall on roof. ie: "54B" or "B4"

2. All cars must use an AMB 160 or 260 transponder.(Castrol ) (Can be rented at track)

3. Bandits and Outlaws

- Castrol  - Bandits and Outlaws will be separated for heat races. Features will be run together. Outlaws will start behind Bandits on all starts. outlaws will move out of position and fall back ( in order) to the rear of the bandit field.

- Sangudo - The 2 divisions will have their own respected heats and features.

4. Combined points from all N.A.M.S races will be totaled to make up the 2019 points. N.A.M.S will be running points races at Castrol Raceway and Sangudo Speedway.

Points awarded will be towards:

-NAMS overall Points

-Bandit Champion

-Outlaw Champion

-Rookie of the Year

-Mini Mayhem Champion ( 2day Invitational Champion)

-Dirt Vs Pavement Champion (Pavement race Champion)

5. -Racecivers will be mandatory in 2015 For all NAMS Events. Racecivers are available to be purchased at Laforce Racing (Contact Kathryn by phone 780-212-7189 or E-mail [email protected] ) or ProWest Motorsports ( Contact Ron by Phone 780-474-2900)

6. Line ups will be made at within 10 mins of the end of the pit meeting. Line ups are built based on a pill draw at beginning of the day.

7. Points are awarded to Car number. Maximum of 2 drivers can collect points for a single car number. Drivers must be registered with the car number at beginning of the year.

READ THIS:

If there is an item not covered or you’re not sure about something in

these rules, have it approved by the tech Inspector or leave it stock!

IF IT DOESN’T SAY YOU CAN DO IT,

ASK YOUR CLASS REP FIRST!!

Cole Rogers 2013 and 2014 NAMS Points Champion

2018 Northern Alberta Mini Stocks -Bandits


1. Cars:

-Any naturally aspirated passenger car with a wheelbase of 109" or less (measured at the track), with a combined factory horsepower and torque rating not to exceed 295 (ie 145hp/145tq or any combination not to exceed a combined total of 295). Car must be at least 5 years old. Front wheel drive or rear wheel drive (no 4x4). Automatic or manual transmission. No convertibles. No Mazda rotary motors. All vehicle and component identification numbers (VIN, motor, trans, etc.) must remain intact and unaltered.


2. Maintenance/Repair:

-Interchange of parts between same Make and Model is allowed.  Interchange of parts between different sub-models (ie: LX, LS, GT, SE) of the same  make and model is allowed, with the exception that it does not violate any of the other rules described herein. Examples: Swapping a 1.8L DOHC engine (or parts from the engine) from a 1992 Escort GT into a 1994 Escort LX that originally came with a 1.9L SOHC engine IS allowed because the Escort GT engine falls below the class combined horsepower and torque limit and they are the same make, model, and generation. Swapping a Dodge Neon SRT-4 engine (or parts from the engine) into a Dodge Neon SE model is NOT allowed, the SRT-4 model is not allowed to race in the class because it is above the combined horsepower and torque limit. This applies to swapping all other components/parts as well. The intent of the parts interchange rule is to allow for budget friendly repair and maintenance of the race car with readily available parts, NOT to enhance horsepower through parts swapping with different sub-models or reduce power-to-weight ratios using different car generations. If in doubt, contact the class rep prior to performing any maintenance with parts of a different year or sub-model.


3. Mandatory Safety Equipment:

- Full-face Snell-rated SA2010 helmet required.

- Fire proof race suit, 1pc or 2pc, single layer minimum (3 layer or better recommended)

- Aluminum racing approved seat, mounted to the roll cage with minimum 4x 3/8" bolts. Minimum of two bolts in the lower seat mounts and two bolts mounted to the main roll cage hoop back bar. (Full containment seat or head restraint recommended)

- Window net, secured to the roll cage only (not car body).

- 5-Point racing harness, 4 years old or newer, secured to roll cage only.

- Fire proof gloves and fire proof shoes mandatory, neck brace strongly recommended

- No Mirrors Allowed  All mirrors will be removed before racing starts. Anybody caught with a mirror in their car will lose all points for the day.


4. Roll Cage:

-Minimum requirement (entire cage, kickers, seat support, door bars, etc.) 1.500" (1-1/2") Diameter x .095" wall thickness structural tubing (DOM or HREW). No black pipe. 1.625" or 1.750" Diameter x .095" wall DOM recommended.

- Floor Plates; Cage must be tied into floor plates (minimum 4 plates, minimum .125" thick, minimum 36 square inches each, welded or bolted through floor or rear seat riser), or 2" square tubing welded to rocker panels/structural components.

- Main Hoop; one continuous hoop behind the driver, from the left side of the driver seat floor, up to the roof, across the top, and back down on the right side of the passenger seat. *Ensure that the main hoop is higher than your helmet when sitting in your seat*

- X-Brace; the main hoop requires an x-brace. One bar from the top left to the bottom right, and one bar from the top right to the bottom left.

- Roof/Down Bars; two bars running from the top of the main hoop, extending forward roughly horizontally along the roof, then down following the windshield pillar slope, then roughly vertically to the floor. One center roof bar is also required from the top center of the main hoop to the center of the top windshield cross bar. *Ensure that the roof bars are higher than your helmet when sitting in your seat*

-Windshield Cross Bars; one horizontal bar at the top of the windshield connecting to the roof/down bars on each side, and one horizontal bar at the bottom of the windshield connecting to the roof/down bars on each side.

- Heavy gauge screen or minimum four ¼" bars in front of driver (from top to bottom of windshield opening).

- Door Bars; minimum two horizontal door bars on the driver side, 12" apart, with five vertical connector bars between them equally spaced along the length. Three or four horizontal door bars on the drivers side and more vertical connector bars recommended. Door bars not required on passenger side but recommended.

- Crush Bars; driver side crush bar to run vertically from roof/down bar near the windshield to top horizontal door bar. Same on passenger side (if door bars are present on passenger side). If no door bars are present on the passenger side, run the crush bar from the roof/down bar near the windshield to the front passenger floor plate or lower bar.

- Seat Mount; seat structure and mounts must tie into the roll cage, NOT the car body.

- Subframe; Subframe connectors may be run under the car and welded/bolted to the floor plates, or inside the car near the floor between the main hoop and front down bar.

- Kickers; Kicker (Front/Rear hoops) bars are optional but recommended.

- Bracing; bars or x-bracing is allowed between rear/front strut towers (Front strut brace must bolt in, not weld). Additional roll cage bars/bracing are allowed. The above is the minimum requirement only.

Roll Cage Diagrams Can Be Found On The Last Page

5. Body/Interior:

- All upholstery, carpet, glass, emblems, air bags, and plastic trim must be removed.

- Dash may remain or aftermarket gauges may be used.

- No removal (gutting) of metal is allowed of any kind with the exception of the interior door structure to fit the roll cage door bars (factory door plate must remain).

- Doors are to be rivoted, welded or bolted shut. Trunks and hatches need to be secured (weld, chain, bolt, or hood pins).

- Hoods are to be secured with hood pins.

- Cover any holes in the front and rear firewalls and floor.

- Bumper covers are to be OEM stock, or similar in appearance to stock(Aftermarket oval track nose), and must be on the car at the start of the race. Bumpers may be repaired with no greater than 3" x 3" x .125" wall square tube and need to fit completely under the bumper cover with no sharp edges.

- Enlarging or pounding out fenders to allow for larger tires is allowed.

- Driver side and passenger side door plates allowed. No grader blades. Must extend 6" past the door in either direction and be bolted through in at least 4 spots (one on fender, two on door, one on rear door or quarter panel) with ½" hardware. Hardware should not protrude any more than necessary.


6. Engine:

-OEM STOCK 4cyl or 3cyl engines only, specific to the make and generation of car used, and at least 5 years old. Carburation or fuel injection OK. SOHC or DOHC OK. Must be below maximum horsepower/torque limit in section 1.

- No aftermarket performance parts, modified parts, or otherwise enhanced parts (ie: non-OEM spec cams or other valve train parts, cam modification/grinding, head work to improve performance, non-OEM spec pistons, etc.)

- No interchange of parts with models or trim levels that exceed the class combined maximum horsepower and torque rating.

- No rotary engines, turbos, or superchargers (engine must be naturally aspirated).

- Removal of air conditioning system and power steering system is OK.

- Aftermarket radiators/fans OK, but must be mounted in the OEM location and of similar dimensional size.

- Engine management computer must remain OEM stock and be the only direct source of engine control. No computer chips or program alterations (ie; increasing rev limiter, altering air/fuel ratio, etc). No standalone aftermarket engine control units or piggyback control units.

-Single un-modified 350 cfm carburetor allowed.


7. Drivetrain:

- OEM STOCK drivetrain only, specific to the make, model, and generation of car used, and at least 5 years old.

- No aftermarket performance parts, modified parts, or otherwise enhanced parts (ie: aluminum flywheels, performance clutches, etc.).

- No gutting of transmission internals allowed (must function in all gears). *Min ¾" inspection hole required for tech to scope flywheel/clutch*

- Locked/welded differentials are permitted.

- No brake bias or proportioning valves allowed. All four wheels must lock up.

- Larger wheel studs and/or wheel bearings/hubs on right side of car may be allowed in certain instances for safety reasons. Contact the class rep.


8. Chassis/Suspension:

-OEM STOCK suspension only, specific to the make and model of car used, and at least 5 years old.

- No aftermarket performance parts, modified parts, or otherwise enhanced parts (ie: lightened components)

- Battery must be secure. No bungee cords or ratchet straps. Battery may be relocated or remain in OEM position. If it is relocated, it must be mounted securely in an enclosed battery box.

- Stock fuel tank OK (factory fuel cutoff switch must remain and be functional). Aftermarket racing fuel cells are allowed. Aftermarket racing fuel cell must be secured with approved tank straps and completely closed off from the driver compartment with a firewall. Fuel line running through car must be steel, maximum 3/8" diameter. Aftermarket electric fuel pumps are allowed (not to exceed factory fuel pump flow rate). Aftermarket pump must have a clearly marked shutoff switch within the drivers reach while strapped in.

-Max of 2in of camber ( in or out) measured with driver in the car.

-Adjustable lower Ball joints ( without modifying  the control arm , hub or spindle) allowed . Offset control arm bushings allowed.


9. Emissions:

-Removal of emission control components is allowed (air pump, EGR, etc.).

- Headers allowed.

- Removal of factory exhaust system (catalytic converter, muffler, etc.) is allowed.

- Exhaust must be directed under car (no open headers), maximum 3" diameter.

- Stock throttle body must remain unaltered. Air intake system can be stock or replaced with an aftermarket tube and cone filter. Stock MAF sensor must be used as close as possible to stock location. Aftermarket air filter needs to be in the stock air filter location.

- Pump gas only, maximum 94 octane (no E85, no aviation gas, no race gas, no methanol, no alcohol, no fuel additives, etc.)


10. Tires:

-D.O.T approved radial, Highway spec, passenger car tires Only. No "LT" rated tires.

- M&S and winter only rating acceptable, but no aggressive mud/truck tires. 

- Maximum 225mm tread width (225/??R??) , any aspect ratio (sidewall height), any rim size.

- Steel or aluminum rims allowed, .Max 7in wheels( no bead locks).

- No altering of tires (ie: softening), no grooving, no siping, no narrowing the tread width, etc.  

-Wheel spacers are allowed, maximum 1" thick.

-Stock wheel nuts allowed to be used with stock style wheels . 1in wheel nuts must be used when using steel racing wheels.

- Min. 3in backspacing on all wheels .  * Updated Feb 19 / 18




11. Pavement Amendment

(With the introduction of a full time Pavement surfaced facility to N.A.M.S , there will be a few rules that are amended due to safety, cost and show quality.)  These rules only apply to races being completed at Hythe Motor Speedway.

-Mirrors allowed

-790 Hoosier Tire Allowed

-Cars will Qualify each race day - Points will be awarded for Qualifying.